[China] as a whole wardrobe wardrobe network is one of the most fashionable wardrobe nowadays, it can be said to lead a whole closet industry. So how is the open overall wardrobe installed? In fact, it is not difficult, knowing that it is different from the traditional wardrobe. Below, everyone with the Chinese wardrobe net small series together with the overall wardrobe installation steps.
Open overall wardrobe installation step one
Use a cloth to place the floor, first assemble from the wide side panel against the end of the wall, and lay the wide side panel on the ground (maintain 700mm away from the rear wall). First, put the plate of the filled three-in-one rubber plug on the cloth, check the hole spacing and the drawing, and install the three-in-one single-link. Then the solid layer is nailed to the cork, fixed on the wide side plate, the top handle with the large handle hole facing upward, the other solid layers are facing downward, and the foot line large handle hole is facing inward (the middle solid layer is consistent with the L frame height, that is, the bottom plate to the solid layer The inner space is 960mm, and the hole is drilled on site.) Put the side panels, nail the cork, and the cork is required to connect the solid layers on both sides. Install the double connecting rod on the second cabinet. Note that the large handle on the double connecting rod can only lock half, that is, 90°. When the two solid layers are fixed to the side plates, tighten the large handles at the same time. Repeat the installation steps for the second cabinet when installing the third cabinet.
Open overall wardrobe installation step two
Nail back plate. Place the assembled whole cabinet on the floor of the point cloth, and lay the side panels in the same plane. Use a slider to measure the diagonal size of the cabinet and adjust it to the same level. Start with the first backing plate from the wide measuring board. Note that if there is a solid nail in the middle, draw the center line of the solid layer with a pencil and nail it. nail.
Open overall wardrobe installation step three
Installation of the L frame. Use the side plates of the L frame to have a parallel line on the corresponding side plates, then move the center line of the three-in-one rubber particles up by 9 mm, and draw a parallel line on the corresponding bottom plate with the top frame of the L frame. The inner center 9mm draws the center line of three rubber pieces. The hole was drilled with a 10 mm drill bit and the hole depth was 10-20 mm. Install a single pole. After the L frame is installed, nails are fixed on the back plate.
Open overall wardrobe installation step four
Clean up the wardrobe installation debris, one person at the left and right, the wardrobe is slightly inclined backwards, lifted hard, and moved back to the desired position. Be careful not to scratch the floor or the wall.
Open overall wardrobe installation step five
Push-pull mirror installation. The three-section rail is mounted on the push-pull mirror, and the height of the push-pull mirror is generally 1700 mm above the bottom solid layer (customer can request height). The rail transverse line is drawn on the side panel at a height of 90° according to the required height. The parallel distance between the new eyes in the three-section track on the upper line is measured, and accurate data is obtained. The lower track transverse line is drawn on the side plate with a 90° angle. Install the upper and lower mother rails of the push-pull. The mother rail is 5mm away from the backboard and is equipped with a push-pull mirror.
Open overall wardrobe installation step six
Installation of the clothing. Move the 38mm draw cross-cut line from the ground level, the side plate is divided into the vertical cut line, and the cross pad is the center position of the first eye above the clothes pass.
Conclusion: It seems that the installation method is simple. I hope that you can carefully install it. In the process, a screw is also very important. It is well installed and paves the way for future use.
Multipurpose wire baskets can definitely bring more convenience for your life. All products are under strict inspections to ensure each piece has good strength and stability. Unique metal frame with guardrail design, which can better prevent the things on the shelf from falling. Hold your shampoo, soap, conditioner, lotions in the bathroom.
Wire Baskets,Bathroom Accessories Tray,Toilet Paper Holder Basket,Toilet Paper Storage Basket
Kaiping Yufa Sanitary Ware Co.,ltd , https://www.dlsen-faucet.com