Rat Interleukin-1 (IL-1) ELISA Kit
(Used in serum, plasma, cell culture supernatant and other biological fluids)
principle
This experiment uses the double antibody sandwich ABC-ELISA method. The anti-rat IL-1 monoclonal antibody was coated on the enzyme labeling plate. The IL-1 in the standard and the sample was combined with the monoclonal antibody. Biotinylated anti-rat IL-1 was added to form an immune complex and connected to the plate On the above, the horseradish peroxidase-labeled Streptavidin is combined with biotin, the substrate working solution is added, the blue is added, and finally the stop solution sulfuric acid is added. The OD value is measured at 450nm. Draw a standard curve to find the concentration of IL-1 in the specimen.
Kit composition (stored at 2-8 ° C)
Coated Wells
96 wells
Enzyme Conjugate
12ml
10 × Sample Buffer
12ml
20 × concentrated washing solution (Wash Buffer)
50ml
Standards (Standards): 30ng / bottle
2 bottles
Substrate working solution (TMB Solution)
12ml
The first antibody working solution (Biotinylated Antibody)
12ml
Stop Solution (Stop Solution)
12ml
Prepare reagents and collect blood samples
1. Collect specimens: serum, plasma (EDTA, citrate, heparin anticoagulation), cell culture supernatant, tissue homogenate, etc. as soon as possible, stored at 2-8 ℃ for 48 hours; longer time must be frozen (-20 ℃ Or -70 ℃), avoid repeated freezing and thawing.
2. Preparation of standard solution: add 3ml of distilled water to mix well before use to make a 10ng / ml solution. Set 8 standard tubes, add 900ul of sample dilution in the first tube, and 500ul of sample dilution in the second to eighth tubes. Add 100 ul of standard solution of 10 ng / ml to the first tube and mix it. Then aspirate 500 ul with the sampler and move to the second tube. Repeat the dilution in this manner repeatedly, draw 500ul from the seventh tube and discard it. The eighth tube is a blank control.
3. The 10 × specimen dilution is diluted 1:10 with distilled water (example: 1ml concentrated dilution + 9ml distilled water).
4. Washing solution: 1:20 dilution with redistilled water (example: 1ml concentrated washing solution is added with 19ml of redistilled water)
Testing procedures
1. Add sample: add 100ul of standard or sample to be tested to each well, mix the reaction plate thoroughly and place at 37 ℃ for 120 minutes.
2. Wash the plate: wash the reaction plate 4-6 times with the washing solution, and print it on the filter paper.
3. Add 100ul of the first antibody working solution to each well. The reaction plate was mixed thoroughly and then placed at 37 ° C for 60 minutes.
4. Wash board: same as above.
5. Add 100ul of enzyme-labeled antibody working solution to each well. Place the reaction plate at 37 ° C for 30 minutes.
6. Wash board: same as above.
7. Add 100ul of substrate working solution to each well, and place in a dark place at 37 ℃ for 15 minutes.
8. Add 100ul of stop solution to each well and mix well.
9. Measure absorbance at 450nm with a microplate reader within 30 minutes.
Result calculation and judgment
1. All OD values ​​should be calculated after subtracting the blank value.
2. With the standard products 1000, 500, 250, 125, 62.5, 31.2, 15.6, 0 pg / ml as the abscissa, and the OD value as the ordinate, draw a graph on the graph paper and draw a standard curve.
3. According to the OD value of the sample, find the corresponding IL-1 content on the graph.
Kit performance
1. Sensitivity: The minimum detection concentration of IL-1 is less than 8pg / ml.
2. Specificity: simultaneous detection of recombinant or natural rat IL-1. Does not cross-react with other cytokines in rats.
3. Repeatability: The coefficient of variation within the board and the board is less than 10%.
Precautions
1. The above standard holes and samples to be tested are recommended to be re-holes, and the standard curve should be made at the same time for each measurement.
2. The washing process is critical. Insufficient washing will lead to an increase in accuracy error and OD value.
3. After opening the slats, the remaining slats should be sealed again to keep the slats dry.
4. This kit should be stored in a 4oC refrigerator.
5. This kit is for scientific research only, not for clinical diagnosis!
WHY WOODEN PLAYSETS?
With today`s options for playsets and swings, it`s surprising to some that wooden playsets and swings are still quite popular. There are a few reasons for this:
Wood is attractive:
Many parents and organizations prefer the look of solid wooden playsets. Making these items from natural materials such as wood blend in nicely with outdoor environments, such as trees and grass, and the natural shades and grain add a natural beauty to your swings and wooden playset. The material utilized in wooden swing sets also provides durability in a wide range of outdoor temperatures since solid Cedar is highly durable and resistant to the change of seasons. As long as the timber has a low moisture content, it will not rot and will look better when compared to plastic or metal playsets exposed to the same weather.
Wooden-based play equipment has an environmental benefit:
Building your Playground Equipment out of high-quality wood vs plastic or metal equipment is actually better for the environment. Wood is a sustainable resource which is able to hold up better than other designs to the outdoors without the need for extensive chemicals or treatments. When you make a playground from wood, it can be repurposed and reused. Plastic and metal options are much less likely to be altered and when their life is over they become just another piece of toxic waste which goes into a landfill. Trees will always be the best option for working on a building a playset and they enable Superior Play to offer a more green alternative for discerning parents and organizations!
Wooden Playground Equipment,Wooden Garden Play Equipment,Wooden Outdoor Play Equipment,Commercial Wooden Playground Equipment
Shenyang Golden Childhood playground equipment CO.,LTD , https://www.outdoor-playground.com