First, the degree of printing paper sizing is not balanced, the paper surface layer caused by the poor smoothness of the ink
The process practice shows that the paper has a large amount of rough ink absorption. When printing paper with poor surface smoothness. The layout of the ink layer is prone to flowering. This is due to the fact that the paper fibers interweave to create a certain gap and are not covered uniformly by the coating layer. In this case, there is a poor contact between the paper surface and the ink layer on the surface of the printing plate at the time of imprinting. In this case, if it is considered that the ink supply volume is insufficient and the amount of ink is blindly increased, it is bound to result in a dirty printing product. Failure is not desirable. Instead, it should increase the pressure of printing. The smoothness of the paper and the layout of the ink layer, to achieve a uniform and adequate contact conditions for printing, so as to achieve a good print to eliminate the printed version of the ink layer phenomenon, to ensure that the printing ink layer uniform and flat.
Second, the printing plate bottom is not solid enough, the printing ink caused by the printing pressure is weak
With respect to the embossing pattern printing process, what kind of bottom pad printing plate is used has a great relationship with the printing ink layer. The test and process practice clearly show that the traditional backward plywood is used as a printing plate base, not only has many drawbacks (such as the printing plate printing rate is low, overprinting is not allowed, etc.), but also prone to ink layer transfer bad phenomenon, causing the layout Inequality and lack of ink occur. This is mainly because the wooden pallet itself is not strong enough, the possibility of compression deformation, resulting in unstable printing pressure, the ink layer on the layout can not be evenly transferred to the printed sheet, this situation is often easily mistaken for lack of ink. On the other hand, due to the poor flatness of the wood tray, it can not meet the normal ink and ink transfer layout. If a multi-layer plywood is used as the bottom bracket, when the field proofs are printed, the thickness of the entire ink layer is often very different. Some inks on the layout are obviously colored, some of the inks are slightly pale, giving people ink. Insufficient ink illusion. The increase in the amount of ink, the layout of the partial pale ink, the visual effect is better, but doing so is also very easy to cause dirty products, and will produce overprint and other ills, it is not desirable. The best way is to not only take good care of the pad printing operation, but also to print a large-area plate, such as a web with a web size of 16 or more. It is better to use a smoother, more solid metal plate, which will prevent it. The phenomenon of black ink on the layout.
Third, the rubber roller is too hard or the position of the ink roller is badly adjusted. The ink layer of the ink layer caused by the uneven distribution of the ink and ink is usually printed with a large number of pages and a large amount of ink, and the large-format printing is required. A uniform and moderate ink coating is obtained. If the rubber roller is too hard, uniform ink transfer and ink distribution cannot be achieved, because the roller is hard and its viscosity is weak, which is not conducive to ink transfer. On the other hand, the ink transfer roller, the ink distribution roller, and the ink application roller, respectively, can not be well connected with the ink fountain roller, the chain iron roller, and the printing plate, and are also the cause of printing ink on the printing plate surface. In this regard, careful analysis and inspection should be carried out one by one, and it is found that there is a gap in poor regulation, and the clearance should be adjusted again. For the shaft head, shaft hole wear caused by clearance, repair measures should be taken. In this way, we can better avoid the phenomenon of product layout caused by ink transfer and ink inhomogeneity and ensure printing quality.
Fourth, the anti-sticking agent in the ink does not mix evenly, resulting in weak ink affinity on the layout, and the ink layer on the layout caused by poor ink transmission.
Printing plate products, after adding anti-adhesive ink, can play a certain anti-sticking effect. If the amount of anti-adhesive agent is too much, for example, more than 4% or the anti-sticking agent does not mix loosely in the ink, it cannot penetrate into the ink evenly. After the coarse anti-blocking agent is spread to the plate, it affects the printing plate. Ink-receptive, the printed page layout will be flower-like. Therefore, if you want to turn off the technology of the ink transfer process and use an anti-adhesive agent, you should first use a suitable amount of bright oil or varnish, and then add the anti-adhesive agent to be added to the ink into a paste and add it to the ink. The liquid release agent can penetrate into the ink more easily, and not only can obtain a better anti-adhesion effect, but also can prevent the occurrence of the phenomenon of flowering of the ink layer of the printed product.
The process practice shows that the paper has a large amount of rough ink absorption. When printing paper with poor surface smoothness. The layout of the ink layer is prone to flowering. This is due to the fact that the paper fibers interweave to create a certain gap and are not covered uniformly by the coating layer. In this case, there is a poor contact between the paper surface and the ink layer on the surface of the printing plate at the time of imprinting. In this case, if it is considered that the ink supply volume is insufficient and the amount of ink is blindly increased, it is bound to result in a dirty printing product. Failure is not desirable. Instead, it should increase the pressure of printing. The smoothness of the paper and the layout of the ink layer, to achieve a uniform and adequate contact conditions for printing, so as to achieve a good print to eliminate the printed version of the ink layer phenomenon, to ensure that the printing ink layer uniform and flat.
Second, the printing plate bottom is not solid enough, the printing ink caused by the printing pressure is weak
With respect to the embossing pattern printing process, what kind of bottom pad printing plate is used has a great relationship with the printing ink layer. The test and process practice clearly show that the traditional backward plywood is used as a printing plate base, not only has many drawbacks (such as the printing plate printing rate is low, overprinting is not allowed, etc.), but also prone to ink layer transfer bad phenomenon, causing the layout Inequality and lack of ink occur. This is mainly because the wooden pallet itself is not strong enough, the possibility of compression deformation, resulting in unstable printing pressure, the ink layer on the layout can not be evenly transferred to the printed sheet, this situation is often easily mistaken for lack of ink. On the other hand, due to the poor flatness of the wood tray, it can not meet the normal ink and ink transfer layout. If a multi-layer plywood is used as the bottom bracket, when the field proofs are printed, the thickness of the entire ink layer is often very different. Some inks on the layout are obviously colored, some of the inks are slightly pale, giving people ink. Insufficient ink illusion. The increase in the amount of ink, the layout of the partial pale ink, the visual effect is better, but doing so is also very easy to cause dirty products, and will produce overprint and other ills, it is not desirable. The best way is to not only take good care of the pad printing operation, but also to print a large-area plate, such as a web with a web size of 16 or more. It is better to use a smoother, more solid metal plate, which will prevent it. The phenomenon of black ink on the layout.
Third, the rubber roller is too hard or the position of the ink roller is badly adjusted. The ink layer of the ink layer caused by the uneven distribution of the ink and ink is usually printed with a large number of pages and a large amount of ink, and the large-format printing is required. A uniform and moderate ink coating is obtained. If the rubber roller is too hard, uniform ink transfer and ink distribution cannot be achieved, because the roller is hard and its viscosity is weak, which is not conducive to ink transfer. On the other hand, the ink transfer roller, the ink distribution roller, and the ink application roller, respectively, can not be well connected with the ink fountain roller, the chain iron roller, and the printing plate, and are also the cause of printing ink on the printing plate surface. In this regard, careful analysis and inspection should be carried out one by one, and it is found that there is a gap in poor regulation, and the clearance should be adjusted again. For the shaft head, shaft hole wear caused by clearance, repair measures should be taken. In this way, we can better avoid the phenomenon of product layout caused by ink transfer and ink inhomogeneity and ensure printing quality.
Fourth, the anti-sticking agent in the ink does not mix evenly, resulting in weak ink affinity on the layout, and the ink layer on the layout caused by poor ink transmission.
Printing plate products, after adding anti-adhesive ink, can play a certain anti-sticking effect. If the amount of anti-adhesive agent is too much, for example, more than 4% or the anti-sticking agent does not mix loosely in the ink, it cannot penetrate into the ink evenly. After the coarse anti-blocking agent is spread to the plate, it affects the printing plate. Ink-receptive, the printed page layout will be flower-like. Therefore, if you want to turn off the technology of the ink transfer process and use an anti-adhesive agent, you should first use a suitable amount of bright oil or varnish, and then add the anti-adhesive agent to be added to the ink into a paste and add it to the ink. The liquid release agent can penetrate into the ink more easily, and not only can obtain a better anti-adhesion effect, but also can prevent the occurrence of the phenomenon of flowering of the ink layer of the printed product.
The Leather Mobile Phone Cover with the protect function , and you could put the card slots ,it more convient you life .It could fit all phone size , Like S, M and L size (4.7-5.5).We sell Pu/genunine Leather Phone Case,card Slot Phone Case ,folio Phone Case , Card Slot Back Cover,Leather Mobile Phone Cover,Universal Leather Case.
We employ the most creative designers and tech brilliant engineers to make the best cases. We believe our high-quality products with competitive prices will satisfy your needs.
The productive process :
Make the Products Mould –Cutting the fabric –Do the half products – Finish products – Cleaning –QC- Package – Shippment .
Leather Mobile Phone Cover
Leather Phone Case,Leather Phone Cover,Leather Mobile Phone Covers,Custom Leather Phone Case Cover
Guangzhou Ysure Electronic Technology Co., Ltd. , https://www.ysurecase.com